![Turbo Lab America](/img/default-banner.jpg)
- 742
- 8 745 302
Turbo Lab America
Приєднався 30 тра 2012
I’m an expert in turbo charger repair. I design, develop, and distribute upgraded turbo repair parts. I operate a cnc lathe and milling machine. Quality check is a major part of my work, and also a major concern in the industry that is often over looked.
Відео
Machining vband turbine housing for correct vband .
Переглядів 9036 днів тому
Evo X t51r mod machine work
Переглядів 31311 днів тому
Evox factory t51r
Переглядів 42011 днів тому
Watch where you are drilling that’s a coolant port
Переглядів 34413 днів тому
BMW N54 intake manifold seals from Amazon failure
Переглядів 21614 днів тому
Viv 17t turbos inspection before rebuild
Переглядів 55614 днів тому
Custom Made T4 Ballbearing GT35R 6567
Переглядів 87121 день тому
Bmw N54 mmp turbo problem
Переглядів 36926 днів тому
Turbo rips apart #turbo #automobile #diesel
Переглядів 1,4 тис.27 днів тому
Bmw e90 335i n54 spawon radiator install
Переглядів 18529 днів тому
Customer messed up rebuild
Переглядів 747Місяць тому
Cracked turbo exhaust manifold
Переглядів 1 тис.Місяць тому
Bmw N54 TD04 bearing housing thread repair
Переглядів 606Місяць тому
BMW E90 alarm system retrofit
Переглядів 378Місяць тому
none of them will fit without = MASSIVE ENGINE UPGRADES !
Nice work!👍
So r u keeping the stock vnt rings or u changing them. I'm planning to try to diy a hybrid gtb22 but im confused with what ur doing with the vnt ring. Do u change it to a bigger one or just bore it out and limit the vanes !!
The rings are the same. The bearing housing from the lmm gets machined for clearance for the lly turbine. I’m not sure why it’s like that but it locks up on the bearing housing if it’s not machined there when converting from an lmm to an lly turbine
Nice jaws.
I made them meself
🦈
What material do you use for n54 wastegate replacements?
How can I call you
You have a Native American Porsche?
How much would this cost to do?
I want to do this to my evo x turbo are you available
I replaced the antenna and still get inACTIVE message. Also codes 604e RDC system and 6055 wheel electronics front right. ugggggg. checked all tpms in all 4 wheels at discount and all are good
Check to make sure your front right sensor/module is in the wheel well and the wires are in good shape. It’s best to follow the codes. I bought some aftermarket wheel sensors and they always cut in and out in the cold. I’m going to have to go back oem next time .
Hi , can you explain what is the unit of value 1358 ??? Is it vdc or what ??
Its ohms.
Why when I ask your not selling ?
This cover sat here for months until I got a chance to do it. I prefer not to take on jobs that include 40-50 replies of asking about updates on the job . I don’t mind doing it if my online orders are done. I can’t predict what is going to take up my time.
Wow, That looks super nice! He's got be happy with that for sure!👍
What do you think of running a inline filter on the turbo oil feed line ❓
The inline filter is supposed to protect the turbo if the engine goes bad but it can clog up and cause the turbo to go bad. I don’t use one, if my engine had bearing failure I would just clean my turbo out. If it’s really bad the bearing material will destroy the turbo and the filter will protect that from debris.
@@turbolabamerica I feel the same way! I wouldn’t want the filter basket to fill & smoke my turbo….✌🏻
How much for what you did to that pair?
Where to buy the rebuild kit ??
Ok. I took mine apart. And they installed the thin vane design. The height is correct...the width of the vane us smaller than stock What is the advantages of the "thin" design
Why do you not have a phone number
Hope that can be saved!🤔😱
I should complete these today
Meanwhile, my BV39 whistles like a jet
I like Mikalor clamps and JCS Hi-Grip worm clamps. Another but expensive option are honstant tension hose clamps.
I haven’t heard of those. I’ll check them out!
Watched video earlier said Boeing's parts from China are half n half, half titanium half death. Hands down best job/environment/stables. 🙏 Blessings
Do the he351ve and the he300vg have the same size compressor wheel plz help I need my truck fixed asap?!?!?
Most do but there is a 56 x 86mm compressor wheel used on the He300vg with cab and chassis. Otherwise the earlier models have the hx40 59.96 x 86 mm compressor wheel.
@@turbolabamerica so do you think a wicked whew for a he351 would work in my he300vg?
Can you do that mod on mini twin turbos?
Really great info
Wouldn't the amount of thrust against the seal "encourage" the effect?
Nice one bro!
I know this video is ancient but i just found out my car ran this turbo and needs a rebuild is it worth rebuilding and selling?? Needs a new hotside
👍
Can you make a 6266 PTE to 6766 PTE? Possibly ball bearing center?
I learn something new about every time I watch one of Your videos. And I know very little about Turbos! But those Pins looked really rough.The knurling looked really bad. I would think press fit or screw in type Pin would work better. just a guess. I really enjoy these videos!👍
I fixed a set of these before , I may have to watch a previous video I made on that rebuild. I think these are 3000$ maybe more. I really think these are the best turbos for that car if they can be fixed and made reliable .
Carnage😅
How would that happen?
I’m not sure. It’s from dump truck, they were hauling dirt.
Custom seal? Machine the lip on the shaft and then machine down an oversized seal if exists?
Anyone knows if I can fix the e46 coupe/convertible folding up side mirrors the same way? My driver side mirror is stuck for about 5 years now and I finally want to fix that. Goes up by pushing the button, but not going down (only by hand)… I need to fix that shit now!
Are you talking about the mirror adjustment? Can you post a video? I’ll check it out.
@@turbolabamerica hi, unfortunately not about adjustment but the power fold. I have the exact same problem that this dude shows, but no one seems to have a solution, which is ridiculous… in all they years: ua-cam.com/video/SGIPQDkZ0iE/v-deo.htmlsi=8jCrEfclSlS8pOu4
Encourage him to purchase your remans!! I’m saving up for a pair. $1,500.00 is a “more than fair” price to pay. Especially for what I’m trying to achieve. Reliability!!!
I went to your Amazon page. But the image doesn't show this compressor housing...it doesn't say Garrett as well
We changed the compressor housing to a gt4088r housing, the wheel is tge same. The new housings are polished on the outside. The gt4088r housings use a larger diameter oring which is much more durable. The fitment on the truck is the same.
@turbolabamerica I sent an email....if I order from Amazon...how will i let you know it's for the 03/04 powerstroke?
It's amazing the things that You have to go through sometimes in order to get something to fit correctly. 👍
The seller no longer sells this item. I’m going to try to cut it reposition and reweld. I may be able to fix it with a slim fan but I think it will be easier to fix it by cutting and rewelding. If I knew it the fitment would be this poor I would have stuck with my original radiator that I fixed with jb weld
@@turbolabamerica 👍
good grief! what a disappointment sorry man
Wow this was 6 years. I'm getting the car re-tuned soon its been sitting since I got a full block rebuild..
When it is solved from car like video The normal that gate is opened as video or be closed in normal
The wastegate is open when the car is off, the wastegate closes when the engine is started. The wastegate flap will rattle at start up then stop rattling when it’s fully closed (thus rattle happens between 3-5 seconds of initial start up). If it rattles when the cat is running then the adjustment is off the wastegate parts are worn throwing off the adjustment or someone did a repair and didn’t adjust them properly.
@@turbolabamerica thank you for replying I have 319b and 30FF CODES Tried changing boost preasure slenoid And check vacum lines Still proplem And exhaust smell Catless
i love you
Are you talking about the channel locks he used on the snap ring?? That snap ring is designed so that you can use pliers! So he used the correct tool..
Your Animals Pics are so Kuel!💯👍 Thanks for posting!
Hello great, try the motion sensor please.
That's a High Smileage turbofold.
That's seen some action